Review Wireless Remote 4 Channel Input 220VAC 433Mhz (Perkenalan 3 Mode Kerja)

This is a 4 channel remote relay module or wireless switch with a voltage input of 220VAC.
In this video I will review the function of each working mode by providing AC voltage input then making the control circuit.
Let’s take a look at this module packaged in a black box by opening the entire bolt.
Inside there are 4 relays.
There is a small strip hole for the winding cable winding antenna.
Then there is rubber as a cable strip.
Inside the module there is a Pairing or Learning Key.
Then there is the relay working mode which consists of 3 working modes.
Later we will see the differences in each work mode function
and what functions are applied to the three work modes.
Then we turn again to the relay section where each relay has NC / NO terminals,
namely Normally Close and Normally Open.
Then there is a 220 VAC voltage input terminal.
Furthermore, this is a remote transmitter which also consists of 4 buttons following the number of relays on the receiver module.
Here is a picture of one of the basic functions of the application to turn ON/OFF the lights that I will do the wiring method.
First, I plug in the plug

cable to the AC 220V input terminal.
Then I installed the pilot lamp instead of the lamp that was connected in series with a white wire,
which would be connected to the neutral terminal.
Then plug in the red wire to the input terminal as a phase point and connect it to each terminal (C) Common relay.
Then plug in the red wire from the NO terminal (Normal Open) on each relay, namely relays 1,2,3 and 4 to each pilot lamp.
With the Toggle working mode, I press the A, B, C, and D buttons.
You can see that all the lights are on.
Press all buttons again and you can see all the lights go out.
Then I changed the relay working mode to Letched. It was seen that the terminals / pins 2 and 3 were connected.
I tried to press the A, B, C and D buttons, and the lights were visible alternately.
Then press and hold the Pairing button for about 5 seconds
until the Pairing LED lights up again
to delete or reset the settings, it appears that all buttons are not responding.
To pair the remote again, press the learning key once (you see the LED is off)
followed by pressing one of the remote buttons, you can see the LED blinks 4 times,
which means that the remote and receiver have been successfully paired.
I tried to press all buttons again,
it looks like the working mode of the lights has returned to normal.
Then I changed the relay’s working mode to Momentary
so that the terminals / pins 1,2 and 3 were not connected.
I tried to press the A, B, C and D buttons,
the lights appeared and flashed immediately when the button was released.
Then press and hold the Pairing button for about 5 seconds until the Pairing LED lights up again
until the Pairing LED lights up again
to delete or reset the settings,
it appears that all buttons are not responding.
To re-pair the remote, press the learning key once (the LED appears off)
followed by pressing one of the remote buttons,
you can see the LED blinks 4 times,
meaning that the remote and receiver have been successfully paired.
Then I changed the relay working mode to Toggle where the terminals /pins 1 and 2 were connected.
I tried to press the A, B, C and D buttons,
it seemed that all the lights lit up and blinked .
Press all buttons again and you can see all the lights go out.
To extend the remote reach to the receiver, you can extend the winding cable antenna
and then remove it from the casing hole
because in this initial condition the range can only be 5 meters long.
that is the review of the remote module or the 4 channel remote relay wireless switch with input voltage 220V.
and the function of each working mode.
By looking at some of the working modes that I have reviewed earlier,
if each work mode can be applied to various needs for controlling the work of the tool.
Hopefully this is useful,
if you like this video please klik thumbs up
and if you have questions, leave a message in the comments column and see you in the next video.

%d bloggers like this: